View Full Version : The phantom is comming!
Randy Naylor
07-12-2003, 11:52 PM
I have just finished the paint on my new Phantom 8. This 8 to 12 cell boat is a 24 inches long and a 8 3/4 gerth. It will have its first race at the 2003 Nats. Hear is a look
Randy Naylor
07-12-2003, 11:58 PM
This boat is does not use trim tabs. It is a great rough water and steering boat
Randy Naylor
07-13-2003, 12:01 AM
Some one may notice that this boat was painted in the spirt of Nick Carter's offshore racer. But has some of my tricks in it.
Randy Naylor
07-13-2003, 12:25 AM
This boat was painted with met. Pearls in the sun it should be a treat.
It's beautiful! :)
How much does a boat like that dent the wallet?
DavidJ
07-13-2003, 02:35 PM
What's the deadrise angle? 15 degrees?
Avenger
07-13-2003, 04:13 PM
that is a sweet looking hull! how do you do it????
Randy Naylor
07-14-2003, 03:49 AM
Originally posted by Kmot
It's beautiful! :)
How much does a boat like that dent the wallet?
A full build is not cheap. I can do a break down. As You know I build kits. I do them in stages. This is not on my web site yet but will be as soon as Dick has time. the Paint is $275. right now! this is done with $300. a gallon paint. It never peals when you pull the deck tape up.
Randy
NEW!!!
"Phantom 8"
ABS Plastic Deep V 24
New from BBY the Phantom 8 to 12 cell mono.
This hull has the racy offshore look with all the best hull geometry and is much larger and wider at 24X8.75 inches. this boat requires no trim tabs so it is much faster becuse for superior design. When on a plane it will cut through the rough water like it's smooth as glass! This boat is a Rocket in the corners and accelerates like you won't believe. It comes in ABS.
_ _
ABS-DV24-1 Hull Kit_ _ Hull Kit contains: deck and hull, transom installed, hatch cover, stickers, build sheet and safety info._ _ Suggested Retail$98.00_ _ Sale Price$45.00_ _
_ _
ABS-DV24-2 Race Basic_ _ Race Basic Kit contains: the same as hull kit plus, a special ultra light drive system, special narrow and shortened rudder, flex shaft assembly, servo bracket, push pull rods and seals, stickers, build sheet and safety info_ _ Suggested Retail$187.95_ _ Sale Price$139.00_ _ _ _
ABS-DV24-3 Advanced Kit_ _ Advanced contains the same as the Race Basic plus _SS1 motor and motor mount, RC Hydros electronic speed control, prop, shaft coupler, etc._ _ Suggested Retail$499.00_ _ Sale Price$315.95_ _
_ _
ABS-DV24-4 Almost Ready to Race_ _ Almost Ready to Race contains the same as the advanced kit although this one is all put together. Just add radio, batteries and water._ _
Suggested Retail$660.00_ _ Sale Price$489.00_ _ __
_ _
Randy Naylor
07-14-2003, 03:51 AM
Originally posted by DavidJ
What's the deadrise angle? 15 degrees?
The vee is a 50 degree overall angle.
Randy Naylor
07-14-2003, 03:54 AM
Originally posted by Avenger
that is a sweet looking hull! how do you do it????
I juess it is Luck! I do not know I just work hard 12 hours a day. But I do love what I do and that helps a lot.
DavidJ
07-14-2003, 01:09 PM
What kind of paint is that Randy?
Randy Naylor
07-15-2003, 01:19 PM
Originally posted by DavidJ
What kind of paint is that Randy?
I use Dupont Emron 5000 and House of Color
umax5555
09-11-2003, 03:55 PM
AHHH! Emron the choice of champions!! Just wear your mask when shooting!!
JimClark
09-11-2003, 04:17 PM
Mask heck when we used that stuff on sailboat masts we used to have to get fully suited up and have an outside air source. The thinners are as bad if not worse than the paint is. Good paint but nasty stuff to us.
Jim
Originally posted by umax5555
AHHH! Emron the choice of champions!! Just wear your mask when shooting!!
Tony T
09-14-2003, 08:11 PM
Will a hatch similar to the one on the SC26 be available?
Randy Naylor
09-22-2003, 11:52 AM
It is not in the plans this winter. Sorry
vBulletin® v3.8.6, Copyright ©2000-2012, Jelsoft Enterprises Ltd.